Método Assistido por Computador e Prototipagem Rápida para o Fabrico Personalizado de uma Prótese de Dedo em Banda de Silicone

Nuno Ventura Ferreira; Nuno Leal; Inês Correia Sá; Ana Reis; Marisa Marques

doi:10.20344/amp.5308

Computer-Aided Method and Rapid Prototyping for the Personalized Fabrication of a Silicone Bandage Digital Prosthesis

Authors

Nuno Ventura Ferreira Departamento de Cirurgia. Faculdade de Medicina. Universidade do Porto. Porto. Portugal.
Nuno Leal Instituto de Engenharia Mecânica e Gestão Industrial. Porto. Portugal.
Inês Correia Sá Departamento de Cirurgia. Faculdade de Medicina. Universidade do Porto. Porto. Portugal. Serviço de Cirurgia Plástica, Reconstrutiva e Estética. Hospital de São João. Porto. Portugal.
Ana Reis Instituto de Engenharia Mecânica e Gestão Industrial. Porto. Portugal.
Marisa Marques Departamento de Cirurgia. Faculdade de Medicina. Universidade do Porto. Porto. Portugal. Serviço de Cirurgia Plástica, Reconstrutiva e Estética. Hospital de São João. Porto. Portugal.

DOI:

https://doi.org/10.20344/amp.5308

Abstract

The fabrication of digital prostheses has acquired growing importance not only for the possibility for the patient to overcome psychosocial trauma but also to promote grip functionality. An application method of three dimensional-computer-aided design technologies for the production of passive prostheses is presented by means of a fifth finger amputee clinical case following bilateral hand replantation.
Three-dimensional-computerized tomography was used for the collection of anthropometric images of the hands. Computer-aided design techniques were used to develop the digital file-based prosthesis from the reconstruction images by inversion and superimposing the contra-lateral finger images. The rapid prototyping manufacturing method was used for the production of a silicone bandage prosthesis prototype. This approach replaces the traditional manual method by a virtual method that is basis for the optimization of a high speed, accurate and innovative process.
Keywords: Reconstructive Surgical Procedures; Fingers; Computer-Aided Design; Prostheses and Implants; Silicones.

Downloads

Download data is not yet available.

Downloads

PDF (Português)

Published

2014-12-30

How to Cite

Ventura Ferreira N, Leal N, Correia Sá I, Reis A, Marques M. Computer-Aided Method and Rapid Prototyping for the Personalized Fabrication of a Silicone Bandage Digital Prosthesis. Acta Med Port [Internet]. 2014 Dec. 30 [cited 2024 Nov. 24];27(6):775-9. Available from: https://actamedicaportuguesa.com/revista/index.php/amp/article/view/5308

Download Citation

Issue

Vol. 27 No. 6 (2014): November-December

Section

Case Report

License

All the articles published in the AMP are open access and comply with the requirements of funding agencies or academic institutions. The AMP is governed by the terms of the Creative Commons ‘Attribution – Non-Commercial Use - (CC-BY-NC)’ license, regarding the use by third parties.

It is the author’s responsibility to obtain approval for the reproduction of figures, tables, etc. from other publications.

Upon acceptance of an article for publication, the authors will be asked to complete the ICMJE “Copyright Liability and Copyright Sharing Statement “(http://www.actamedicaportuguesa.com/info/AMP-NormasPublicacao.pdf) and the “Declaration of Potential Conflicts of Interest” (http:// www.icmje.org/conflicts-of-interest). An e-mail will be sent to the corresponding author to acknowledge receipt of the manuscript.

After publication, the authors are authorised to make their articles available in repositories of their institutions of origin, as long as they always mention where they were published and according to the Creative Commons license.